Chunkys Pulsar GTi

BEEF! Get some of this on those badboy sidewalls asap

G7516_Endurance.jpg


Have you got coilovers btw? Rear looks like it needs raisin tad to match front ;)
 
Hally said:
you got a standard exhaust on it?
Click to expand...

Yer its standard atm Hally, but i got a full s/s system from corbs to go onto it and to save hassle i will prob sell my s/s header,downpipe and 3" decat lol
2011-02-12203207.jpg


Psycho_Eddie said:
BEEF! Get some of this on those badboy sidewalls asap

G7516_Endurance.jpg


Have you got coilovers btw? Rear looks like it needs raisin tad to match front ;)
Click to expand...

Will that get rid of the paint on the sidewalls? lol and Nope no coilies buddy, i thin kmy shocks might be shot but there not "bouncy" atall?? so i have jsut left it ftm as im looking for a cheap set of second had coilies lol :D :cool:
 
chunky899 said:
Will that get rid of the paint on the sidewalls? lol and Nope no coilies buddy, i thin kmy shocks might be shot but there not "bouncy" atall?? so i have jsut left it ftm as im looking for a cheap set of second had coilies lol :D :cool:
Click to expand...

Nitromors & a tooth brush will. Bucket of water & a rag to wip it off aswell :)
 
Fitted the clutch, Fidanza flywheel, poly-engine mounts to my car yesterday and then i fitted the 2-slatte grill on my car to see if i like it as im still not sure, :s
2011-03-01154422.jpg

2011-03-01154347.jpg


And also got myself a Mascott too :D
2011-02-19140828.jpg


Mike
 
Psycho_Eddie said:
Exedy clutch it be? review on clutch/lightened fly?

No pictures of clutch/fly :(


2 Slat looks good!
Click to expand...

yer its the Exedy clutch/Fidanza flywheel, the flywheel is amazingly lighter than standard and with it the engine revs alot easier and faster, the clutch bites lovely but i need to adjust mine as its a little high 5 stars mate :D
 
Was on the Roof at work yesterday and a little insperation from Simcard came along lol
2011-03-05101442.jpg


Also I made a steel bracket up to go from my Lambda sensor to my inlet mani to earth it out correctly,
2011-03-05131014-1.jpg

Used a Stepper Drill to get the 18mm needed for the sensor :D
2011-03-05131055.jpg

Then Counter-sink to smooth it off..
2011-03-05131131.jpg

And had this....
2011-03-05131154.jpg

Then Cut/filled till i couldnt be arsed anymore lol to this.....
2011-03-05134116.jpg


But i forgot to get pics of it fitted but i will do :D

Mike
 
Well i havent updated this thread in a while so here we go......

I felt the need to do something different to my car that not alot of other members have (as far as i know) so i modded the boot lights to run with the side lights
2011-03-29200007.jpg


I think it looks sweet IMO :D

I had my first ever run down santa pod and ran a 16.7 seconds... im sure i could do better tbh
193529_10150178274895407_640010406_8323124_2314292_o.jpg

2011-04-10182355.jpg



and whilst waiting around for a mate i got bored and took some pictures :D
2011-04-10112013.jpg

2011-04-10112035.jpg

2011-04-10112128.jpg

2011-04-10112150.jpg

2011-04-10120815.jpg


Mike
 
A Friend got his camera out during a small meet in Newmarket:
1.jpg

2.jpg

4.jpg

5.jpg

6.jpg
,

Also had my Caliper seal kit arrive followed by my cup holder/cubby hole thingy lol
2011-04-20102128.jpg

2011-04-20094017.jpg
 
And Now fitted, went in fine, just swapped the brackets around onto the cup holders, and Voila! well the holes were a little small for the original bolts, but still went in fine :D lol
2011-04-20111311.jpg


And it doesnt obstruct the Gear leaver :D
2011-04-20111642.jpg


Mike
 
You must log in or register to reply here.
Back
Top Bottom