REAR WIPER MOD

[rocky-crowder]

HI GUYS CAN ANY1 TELL ME HOW 2 DO THE REAR WIPER MOD SO ITS SITS AT THE BOTTOM OF THE WINDOW RATHER THEN THE SIDE PLEASE

 

[CoV]

I can once I've got rid of my headache from your shouting!

 

[tw33k]

her you go mate http://www.almeraownersclub.com/threads/parking-rear-wiper-along-bottom.3928/ and turn caps lock off lol

 

[rocky-crowder]

cheers m8 dident realise i did that post in capiatals lol

 

[rocky-crowder]

wont let me view it cheers anyway m8

 

[rowdy-GTi]

wont let me view it cheers anyway m8

That's a paid members section, so get your wallet out.

 

[wraith]

Take the motor apart and move the pin to the other hole. Done.

 

[tw33k]

Or this works too ^ lol, I always forget about the restricted sections to none members sorry bud

 

[rocky-crowder]

cheers guys

 

[rayner89]

I had ago at doing this today the screws on the back of the motor wouldnt shift! Was just rounding off, any tips on how to undo the case as the screws are so small??

Sent from my GT-S5360 using Tapatalk 2

 

[Spook]

I had ago at doing this today the screws on the back of the motor wouldnt shift! Was just rounding off, any tips on how to undo the case as the screws are so small??

Sent from my GT-S5360 using Tapatalk 2

If you've rounded off the screws you're a bit knackered mate. You can either drill them out of knock the heads off to gain access but then you've obviously got to refit the back. You may be able to get some grips on the shank once its apart though and use new screws. Other than that you could probably find one second hand on here. As you're thinking of selling up though I'd be inclined to leave it alone.

 

[CoV]

First of all you need a quality set of screwdrivers. Those really aren't a tight bunch of screws.

You can drill the heads off the screws. This will release the tension on the threads and allow you to unscrew with your fingers however, you will need to find a set of new screws.

As spook says if you're selling though, why bother?

 

[rayner89]

@Spook Its probably going to the scrap heap and seen as im a total beginer when it comes to motors what better way of me learning than destroying this on

Sent from my GT-S5360 using Tapatalk 2

 

[sss4me]

I had ago at doing this today the screws on the back of the motor wouldnt shift! Was just rounding off, any tips on how to undo the case as the screws are so small??

Sent from my GT-S5360 using Tapatalk 2

http://www.ebay.co.uk/itm/Silverlin...r-Bits-Slotted-Crosshead-427633-/380441383274

 

[rayner89]

Will invest in one of these then...take it thats what you use?

Sent from my GT-S5360 using Tapatalk 2

 

[Spook]

They are good. Especially if you're not used to wrenching ie have the hands of a 12 year old girl.

 

[rayner89]

Haha whats that spose to mean?? I think i pushed against it to hard tbh and the driver was a shit fit it rounded of slightly ill give this ago thanks bud

Sent from my GT-S5360 using Tapatalk 2

 

[Seebeebee]

I'm amazed you managed to round them off. Were you using an over or under sized driver? Nissan didn't use cheese to make the N15's fittings like they did with the the N16.

 

[rayner89]

Well it looked like it fit well but i think the point on the driver was abit long?? If that makes sence i havent fully rounded it off o stopped before i fucked it up even more. Luckly i dont care about the damage ive just about given up with this one now

Sent from my GT-S5360 using Tapatalk 2

 

[tw33k]

get a screwdrivers that fits and tap the end with a hammer to shock the threads should do it